HobbyKing
TURNIGY 450 H2218 BRUSHLESS OUTRUNNER 2100KV
| Model | 2218 |
| Cells | 2~4S |
| No load Current | 1.9A/10V |
| Max power | 500W |
| Weight | 67g |
| Shaft diameter | 3.17mm |
| Dimensions | 27.2 x 36.5mm |
| Recomended ESC | 2~4S/50A |
Turns: 6, Kv: 2100rpm/V,
This motor is specifically designed for the 450 helicopter range ...5 Reviews
HobbyKing
HEXTRONIK DT750 BRUSHLESS OUTRUNNER 750KV
| Required Voltage | 11.1v |
| Suggested Battery Capacity | 1300mAh + |
| Suggested Prop | 11x3.8 or 11x4.7 |
| Max current draw | 18A (with 11x4.7 prop) |
| Max thrust | 1000g+ |
| No Load Current | 1.4A |
| Shaft | 4M (perfectly suited to Towerpor/GWS SF Slow Fly props) |
| Weight | 78g |
| Diameter | 41mm |
| Overall length | 77mm |
Kv: 750rpm/v,
Looks can be deceiving. This outrunner is around twice the ...5 Reviews
HobbyKing
TURNIGY 2730 BRUSHLESS MOTOR 1500KV
| Diameter of shaft | 3mm |
| Length of front shaft | 10mm |
| Magnet type | 45SH |
| Thrust | 290~410g |
| Prop | 7x3.5 or smaller |
| ESC | 10A |
| Max Current | 4.5~8A |
| Lipo Cells | 2-3S |
| Download data files | TURNIGY MOTOR DATA |
Dimension:, 32mm x 27mm, 43mm(with shaft), Weight:, 26g (kv1500) (not including connectors), Lamination thickness: .,
2mm5 Reviews
HobbyKing
C05XL MICRO BRUSHLESS OUTRUNNER 10800KV
| Weight | 6.8g |
| Size | 24 x 13.9mm |
| Max current | 4A/40W |
| Current | 4.2V/0.82A (No load) |
| Shaft | 1.5mm |
| Shaft length | 7mm |
Specification:, Kv: 10800rpm/v,
C05XL Micro Brushless outrunner 10800kv5 Reviews
HobbyKing
TURNIGY AE-45A BRUSHLESS ESC
| Output | Continuous 45A, burst 50A up to 10 seconds. |
| Input Voltage | 2-6 cells lithium battery or 5-18 cells NIMH battery. |
| BEC | Linear 3A @ 5V |
| Control Signal Transmission | Optically coupled system. |
| Max Speed | 2 Pole |
| 6 Pole | 70,000rpm |
| 12 Pole | 35,000rpm |
| Size | 60mm (L) * 26mm (W) * 11mm (H). |
| Weight | 43g. |
| Multiple protection features | Low-voltage cut-off protection / Over-heat protection / Throttle signal loss protection |
| Factory default settings | Brake |
| Battery type | Li-xx (Li-ion or Li-Po) |
| Low voltage cutoff threshold | Soft cut-off (2.6V) |
| Timing setup | Low |
| Soft Acceleration Start Up | Normal |
| Low voltage cutoff type | Medium |
Specification:, Features:, High performance microprocessor brings out the best compatibility with all kinds of motors and the highest driving efficiency., Programming features:, Brake setting (we recommend using brake for only folding props applications),
A quality SMT produced ESC with reliable components. The Turnigy ...5 Reviews
HobbyKing
TURNIGY 480L V-SPEC INRUNNER W/ IMPELLER 1370KV
| Diameter of shaft | 4mm |
| Length of front shaft | 13mm |
| Battery | 4 Cell 4S/14.8V |
| RPM | 1370kv |
| Max current | 60A |
| No load current | 1.0A |
| Internal resistance | 57.10ohm |
| Data | 4S 14.8V |
| Max Current | 17.7A, 19.5A, 25A |
| Pull | 1030g, 1120g, 1300g |
| ESC | 60A |
| Battery Type | 4S Only |
Dimension:, 57mm x 30mm, 70mm(with shaft), Weight:, 143g (kv1500) (not including connectors), Lamination thickness: ., Prop:, APC12x8, APC12x6, APC8x3.8,
High torque inrunner, excellent for running propellers without needing a ...5 Reviews
HobbyKing
TURNIGY G160 BRUSHLESS OUTRUNNER 245KV (160 GLOW)
| Battery | 9~10 Cell /33.3~37V |
| RPM | 245kv |
| Max current | 60A |
| No load current | 10V/1.45A |
| Current capacity | 78A/15sec |
| Internal resistance | 0.03 ohm |
| Diameter of shaft | 8mm |
| Dimensions | 89x64mm |
Weight:, 649g (not including connectors),
Designed to be a direct swap out for your 160 ...5 Reviews
HobbyKing
C2222 MICRO BRUSHLESS OUTRUNNER 2850KV (15G)
| Diameter | 22.2mm |
| Length | 24mm |
| Shaft | 5mm |
| Weight | 15g (with 10cm wire) |
| Power | 60W |
| Resistance | 485 |
| Idle Current | .7A |
| Max amp | 10A (15sec burst) |
| Voltage | 2-4cell Lipoly |
Kv: 2850rpm/v, Turns: 25,
Specifications. We do not have a suggested prop size for ...5 Reviews
HobbyKing
MINI AIR COMPRESSOR (1/8HP) 220-240V
| Type | Piston |
| Power | 1/8HP |
| Max Pressure | 2.8BAR/40PSI |
| Speed/Min | 2900, 220-240V/50HZ |
| Air Flow | 13-15L/Min |
| Dimension(L*W*H) | 18CM*11CM*14.5CM |
| weight | 2.4KGS |
Specifications:, Electric Current:, 0.65A/50HZ;1.4A/50HZ,
Great for small workshops. Low noise and regulated posative airflow ...5 Reviews
HobbyKing
HOBBYKING PARALLEL CHARGING BOARD FOR 6 PACKS 2~6S (XT-60)
| Cell | 2~6S |
| Voltage | 0~22.2VDC |
| Max current | 30A |
| Connector | XT60/jst-xh |
Battery:, 6 packs (same capacity & cell count), Note:, The batteries should have same capacity.,
Our very own in-house designed and built parallel charge board! ...5 Reviews
HobbyKing
TBS MINI PROGRAMMABLE SOUNDUNIT
| Can be fully configured with free PC software | Download from the files Tab below |
| Dimensions | 55x25x10mm |
| Note | Extension wire shown in the photo not included. |
Features:, Fully customer programmable., Technical Spec:, Supplyrange:, 3.5~12V (from receiver), Internal amplifier:, 1.2W at 8 Ohm and 5V supply, Switching outputs:, Minus switching, max. 12V/0.5A each, Weight:6g,
This soundunit is developed specially for electric powered airplanes. And ...5 Reviews
HobbyKing
1/16 BRUSHLESS 4WD MONSTER BEATLE W/ 25AMP SYSTEM
| Motor | Brushless Inrunner(2040) |
| ESC | 25A Brushless (with Reverse) |
| Battery | 2S LiPo (100x40x25mm MAX SIZE) w/ XT-60 connector [Required] |
| Servo | 15g Micro |
| Traction | Full Time 4WD, Twin Diff |
| Length | 280mm |
| Width | 210mm |
| Height | 150mm |
| Groung Clearance | 20~40mm Adjustable |
| Top Speed | 40km/h on standard System |
5 Reviews
HobbyKing
TURNIGY 4 IN 1 TORX DRIVER 1.4~ 2.7
| Head | Torx (hexalobular) AKA Star Bit |
5 Reviews
HobbyKing
TURNIGY TRUST 70A SBEC BRUSHLESS SPEED CONTROLLER
| Brake | off |
| Battery | LiPo Auto Detect |
| Low Voltage | 3.2v (power down motor) |
| Max Motor Current | 70A |
| BEC Voltage | 5.5v (Switching) |
| LiPo | 2~6S |
| NiMH | 5~16cells |
| Weight | 65grams |
Max BEC Current: 3A,
Turnigy® TRUST SBEC ESCs have a very flexible and broadly ...5 Reviews
HobbyKing
NTM PROP DRIVE SERIES 35-36B 1400KV / 495W
| Model | NTM Prop Drive 35-36B 1400 |
| Max current | 53.94A |
| Shaft | 4mm |
| Weight | 117g |
| ESC | 60A |
| Cell count | 3s~4s Lipoly |
| Bolt holes | 18.9mm & 25mm |
Specs:, Model:, Kv:1400rpm/v, Turns:7, Max Power:, 495W @ 12v (3S) / Waiting test results (4S), Bolt thread:M3, Suggested Prop:, Prop test data coming soon!,
NTM Prop Drive motors are rock-solid performance outrunners with tight ...5 Reviews